Voltage is what controls the level of heat going to your coil compared to your resistance to create wattage (which is power). You set the Voltage of the device. So the same power will go to any device, any ohm. Let's say you have a 1.8ohm coil that works well at 3.6 volts, if you swap to a 2.5ohm coil on another device you will get a much different vape because the overall power to the coil has changed because of the added resistance. You would probably then up your voltage to maybe 4.3v to get the same kind of "vape".
For variable wattage you set it once and forget it (sort of) Unlike variable voltage you are setting the end result output. The Device takes into account the ohms and sets the output for you to arrive at the selected watts.
If you set your variable wattage mod to 8.0 watts two things will happen. First the mod will automatically detect the ohms of what you put on it, let's assume a 2.5 ohm cartomizer. Second when you fire your device it will look to see the ohm rating of what your using, and then adjust the voltage, in this case to 4.4 volts, then fire. Likewise, without changing anything, should you swap that 2.5 ohm cartomizer, for a 1.8 ohm atomizer, the device will automatically detect the change in the ohms of your atomizer then fire at around 3.8 volts.
This isn't to say you won't ever change the wattage, you will, depening on the coil type, the liquid or other factors but you will most likley not do it as often.
Leaking is easily preventable. Never let the liquid sit above the top line printed on the atomizer. This can happen if the unit is left upside down or on its side and will cause it to leak. In order for the unit to work properly there must be a hole for the vapour to exit and this is an essential part of your Vapourizer Tank.
We strongly advise you NOT to keep your Tank in your pocket. Due to their long structure, putting it in your pocket puts undue stress on its joints which can cause an array of issues. If you must keep it in your pocket, remove it when you sit down. Please try not to drop or crush it, as it can cause the unit to become misaligned and the joint between the battery and atomizer will weaken, shortening its life span.
If it’s not producing any vapour your atomizer may be empty. Replace your atomizer and fill your atomizer with e-liquid.
If you try to vape without any e-liquid, it could burn out your atomizer which could permanently damage it, making it unusable.
It may be locked! Try clicking the button 5 times (quickly). It will flash a few times and will either lock/unlock itself.
Locking your battery will stop it being activated in your bag/pocket which will prevent burning out your atomizer, using up its charge and wasting your e-liquid.
It is important to lock the device every time you are finished with it, especially if you are around children.
This can sometimes happen if the atomizer has flooded, the cartridge overfilled, or if the e-cig has been drawn on too hard. However, the number one cause is keeping your e-cig upside down or putting pressure on the atomizer by keeping it in your pocket. We suggest keeping it upright at all times to ensure that the liquid is always kept below the top printed line on the atomizer
E-liquid may taste bitter so rinse your mouth out with water if this occurs. Use a paper towel to mop up any excess liquid you can see on and around the e-cigarette and make sure it’s as dry as possible before trying to use it again. Please be rest assured that small amounts of e-liquid will not have a negative impact on your health.
You set the temperature you want the atomiser to run at versus selecting the voltage or power output of the mod. This means that when you press the power button the e-cig mod monitors the temperature and intelligently adjusts the power to keep the coil at the desired temperature and maintain it.
All electronic cigarette batteries must be charged using ONLY the correct charging cable. The USB Charging Cable must ONLY be used in either a USB port on a PC, or with the USB wall adapter.
The light on the battery will flash to indicate a proper connection and the light on the charging cable will turn from RED to GREEN once fully charged. Charging most batteries should take between 3 - 4 hours for a full charge. It is advisable that you only charge your battery once it is completely run down. The light on the battery will flash to indicate the battery is flat and requires recharging.